Mazda 3 Rear Power Window Not Working

Mine is 2010 sedan.

Mazda 3 rear power window not working. When not rolling the windows at rest both the leads going to the window motor are grounds when the switch is pressed for up or down the ground is lifted off one of the leads and 12V is supplied window rolls in one direction when switch is rocked in. Most likely the problem is the switch. The power window regulator motor is now programmed for the express function. Press the window down button to bring the window all the way down and again do not release it for 10s after the window is all the way down.

If there is a power issue within the power window circuit the fuse will blow stopping the flow of electricity to the power windows and preventing potential damage. Have checked fuses both are good. If it doesnt check for a bad fuse and replace it if necessary. You will need to check all connections in door.

Press the switch of each window and fully open the door glass. Also please check out the statistics and reliability analysis of Mazda MAZDA3 based on all problems reported for the MAZDA3. If the fuse blows all power windows in the vehicle as well as any other electric devices that share the fuse will stop functioning altogether. The most recently reported issues are listed below.

For replacing this defective switch you need to take out the window switchboard. Make sure the rear defroster switch and the ignition key are turned on. Car demonstrated is 2006 Mazda 3 but similar proc. Disconnect both wires from either side of the defroster grid and touch one end of your tester to each wire.

Make sure that the power window lock switch located on the drivers door is not depressed. Broken power windows are a real bummer especially if they get stuck down in hot or cold weather. Mazda 3 Service Manual. Pull the switch of each window to the manual-up position to fully close the window and keep holding the switch up at the position for approx.

Pull up the switch to fully close the window and continue holding the switch for about 2 seconds after the window fully closed. Upon battery reconnection the electric windows appear to work normally if the s held down or up however the witch is Auto. Now the car has after-market tinting on the windows it was fitted prior to my purchasing the vehicle and on a particularly hot day about three months ago both of the rear windows just wouldnt go down any more. Continue holding the power window switch for approximately 3 seconds.

Mazda window two-step windows. Drivers window switch controls not working in your Mazda. Press the switch and fully open the window. Press and hold the power window switch until the window is fully UP.

I tried and it works on our Mazda 3. Mazda 3 Automatic Window Reset. Have tried drivers door switch pa read more. Could need simple reprogramming fix shown here.

Continue holding the power window switch for approximately 3 seconds. Check whether power is getting to your defroster grid. Another possible electrical problem that keeps your power windows from working is a faulty window switch. If the light comes on you have power.

In a few hours you can troubleshoot and fix your power windows by following these steps. If the battery in a late model Mazda vehicle is weak or is changed you must perform a power window reset procedure to initialize each window. 2007 Mazda 3 - all power windows stopped working then the drivers window started working again. Mazda MAZDA3 owners have reported 3 problems related to power window under the visibility category.

Power Window Main Switch Inspection. 1 Turn the ignition switch to the ON position. This procedure is commonly required to be performed on a Mazda 3 vehicle with electric windows after battery disconnection. Now take another switch and plug it in the wiring connectors.

Make sure to have a 12 volt test light remove door panel and check window switch for power if ok go to motor hold test light to the hot wire to motor use window switch does test light light up if so motor is bad. You can use a multi-meter for checking the reading of the connectors. Unplug the connectors to ensure that they are offering the suitable 12 volts to the switch. Heres how to do the power window reset procedure.

If the system does not work normally even though the inspection items or related wiring harnesses do not have any malfunction replace the power window main switch. Hold the window up button to close the window do not release the switch for 10s after the window is all the way up. Disconnect the wire closest to the passenger side of the car and attach the test lamp clip to the wire not the little metal tab attached to. Power window motor rear left side See POWER WINDOW MOTOR INSPECTION Related wiring harness.

I didnt have time to bother with it but when idly pressing the button one cooler day one of the rear windows gave a bit of a pop. HondaAcura use a polarity reversing ground at rest power window system same as the door locks.

If you re searching for Mazda 3 Rear Power Window Not Working you've reached the right location. We have 15 images about mazda 3 rear power window not working adding pictures, photos, photographs, backgrounds, and more. In such webpage, we additionally provide variety of images available. Such as png, jpg, animated gifs, pic art, symbol, black and white, transparent, etc